LightRail 4.0 AdjustaDrive Complete Kit

LR46SYS
$303.99

Adjust-a-drive motor w/6' rail plus mounting hardware

The all new LightRail 4.0 AdjustaDrive is the newest linear light mover available from Gualala Robotics Inc.

For a rectangular growing area, a linear lamp moving system is preferable. The self-propelled Light Rail 4.0 Adjust-a-Drive is without question the finest linear lamp-mover available. It uses no pulleys, chains or gears. Simply mount the standard 6 foot track over the desired area and place the lamp-moving drive motor onto the track. The Light Rail 4.0 Adjust-a-Drive is supplied with adjustable switch stops, so lamp travel can be any length you wish. This is perfect for a start-up size garden through to a full growth garden. The standard 6 foot track may also be extended. Light Rail 4.0 comes with a 2 Year Factory Warranty.

With both a 0 to 60 second adjustable time delay for promoting even growth from end to end and a two to four feet per minute adjustable speed that covers a wide range of lamp intensities and travel distances, the all new LightRail 4 AdjustaDrive from Gualala Robotics Inc. is the ultimate in light mover control. Compatible with all LightRail 3.0 and 3.5 rails and accessory items. Designed and manufactured in the USA.

Light Rail 4.0 is rated to 35 lbs
Light Rail 5.0 is rated to 100 lbs

RPM is adjustable from 6 RPM (2 ft/min) to 10 RPM (4 ft/min)

6.2 lbs.
0.0L x 0.0W x 0.0H
120

How much weight can the Light Rail 5.0 carry?

The Light Rail 5.0 can support up to 100 lbs. when mounted properly. Note: the greater the weight, the more frequently trolley wheels will need to be replaced.

What if my Sola Rola travels beyond the magnetic stops?

It needs to be resynchronized. First, remove power from the system. Next, remove the magnets from the track. Then, repeat the process for installing the magnetic stops as listed previously in the manual. Make sure the rails are installed at least 6"

My digital 7-day timer won't come on at my programmed time. Is it defective?

First, make sure it is in Auto mode (the screen says AUTO at the bottom). If that doesn't help, the timer might be in Random mode. Press the WEEK and HOUR buttons simultaneously to toggle Random mode on and off (you'll see a circle appear and disappear on

I'm having trouble programming the digital 7-day timer TM01715(D). Is there an alternate set of instructions?

Step 1: Press PROG. Left side of screen should display 1 ON. Step 2: Press WEEK until the desired week schedule is displayed at top of screen. Step 3: Press HOUR and MIN to set the desired time you want the timer to turn the device on. Step 4: Press

How many lights can I plug into a lighting controller that is wired to 120V?

Running your lights at 120V (instead of 240V) will reduce the acceptable amount of ballasts used by half. For example, an 8 light controller, when wired to 120V, can only have a maximum of four 1000W ballasts plugged in. This is because the amperage drawn

How much weight can the Light Rail 3.5 and 4.0 carry?

If mounted continuously along the rail through all the mounting holes first to a board, and then the board to the ceiling, it will easily carry 75 lbs as long as the board is mounted sufficiently to a structure that will handle the weight. If mounted only

Will this ballast work with a flip box?

If you are using a "Flip Relay Box" and your ballasts are having trouble switching, you must observe the following instructions to ensure proper operation. Most electronic ballasts contain an "error sensing" open circuit safety feature

How do I re-attach my Hydrofarm Light Track trolly to the chain?

The Hydrofarm Light Track has a small pin that attaches the trolly to the chain. There is one link in the chain that is big enough to fit the pin. Refer to the above PDF for a closer look.